Takardun fasaha

Bayanin tsarin ɗakin yashi

1. Amfani da kayan aiki:

Wannan kayan aiki ne don tsabtace workpiece surface, ƙarfafa, tsatsa kau, kawar da ciki danniya, ƙara Paint mannewa, da dai sauransu, ta hanyar harbi peening tsaftacewa, inganta gajiya ƙarfi na workpiece, da kuma a karshe cimma manufar inganta karfe surface da ciki. inganci.

A kayan aiki ga tsarin ne musamman hadaddun, ta hanyar harbi ayukan iska mai ƙarfi ba za a iya tsabtace sama da zarar matattu kusurwa na workpiece, za a iya bi da harbi peening, don tabbatar da surface na workpiece tsaftacewa ingancin.

Na'urar tana da ƙaramin tsari da ƙira mai ma'ana.Gabatarwar ci-gaba da fasaha a gida da kuma kasashen waje, a hade tare da kamfanin shekaru da yawa a cikin harbi peening tsaftacewa kayan aiki zane da kuma samar da m gwaninta zane, tare da high dace da makamashi ceto, harbi peening, high gudun, sanye sassa na tsawon rai. dace tabbatarwa, aminci da abin dogara halaye.

Ii.Yanayin aiki na kayan aiki:

1, ƙarfin wutar lantarki: AC380/3 50Hz

2, matsa lamba iska: 6.3m3/min, 0.5 ~ 0.7mpa

IiiBabban sigogin aikin fasaha na kayan aiki:

1, matsakaicin girman aikin aikin: 17000*3500*2000mm.

2, girman gidan yanar gizo mai tsabta: 20000 × 10000 × 7000m

3. Hawaye

(1) Adadin ɗagawa: 20t / h

(2) Ƙarfin wutar lantarki: 4Kw

8. Mai raba:

(1) Adadin rabuwa: 20t/h

(2) Gudun iska a cikin yanki na rabuwa: 4 ~ 5m / s

9, kasa dunƙule conveyorDandalin a tsaye A)

(1) Samfura: LS250

(2) Na'urar sarrafawa: 20T / h

(3) Motoci: 5.5KW

10, kasa dunƙule conveyordandamali mai tsayi B)

(1) Samfura: LS250

(2) Na'urar sarrafawa: 20T / h

(3) Motoci: 5.5KW

11, na'urar leƙen asiri:

(1) Samfura: KPBDR1760

(2) Girman tanki: 0.4m3

(3) Adadin harbin harbi: 1500 ~ 1900kg/h

(4) Yanayin aiki: ci gaba da feshi

(5) Yanayin sarrafawa: sarrafa hannu

(6) Yawan bindigogin fesa: 2

(7) Diamita na bututun ƙarfe: φ 12mm

(8) Yawan shan iska: 6.5m3/min

(9) Matsakaicin aiki: yashi, harbin karfe, iska

12. Na'urar safarar yashi:

Ƙofar sarrafawa matsa lamba: 0.6 ~ 0.8mpa

13. Mai tara kura:

(1) Samfurin masu tara ƙura: LT-56

(2) Yadda ake kawar da kura: 99.5%

(3) fan kau da kura: 4-72-8C 22KW

(4) Girman iska: 2000m3 / h

(5) Fitar kura: ≤100mg/m3

14. Jimlar ƙarfi: kusan 60Kw

15. Yawan yashi na farko: 2t

16. Tsatsa kau ingancin sa: SA2.5GB8923-88

17, tsarin hasken kayan aiki: ≥ 240LUX

18. Na'urar tushen iska: tushen iska tare da fiye da 6.5m3 / min da matsa lamba na 0.6-0.8mpa (wanda masu amfani ke bayarwa).

Iv.Bayanin Kanfigareshan Kayan aiki:

Kayan aikin ya ƙunshi: ɗakin tsaftacewa, harbi mai tattara hopper, mai ba da abinci na karkace (biyu), hoist, separator, tsarin kula da ciyarwar harbi, tsarin ɗaukar hoto, isar da kayan aiki, layin dogo, tsarin hasken cikin gida, tsarin sarrafa wutar lantarki da sauransu. .

1. Tsaftace abubuwan walda na jikin ɗakin:

Chamber size: 20000 × 10000 × 7000㎜, karfe tsarin kwarangwal ta yin amfani da 150 × 100 × 4, 100 × 100 × 4, 50 × 50 × 4 square tube da δ = 5, δ = 12 karfe farantin samar (mai saye);Ƙananan sito an yi shi da δ = 5 farantin karfe, an ƙarfafa tashar tashar tashar, kuma an shimfiɗa ɓangaren sama da farantin grid;An yi farantin gwanjo da ƙarfe mai faɗi.

1. Ƙofar jikin ɗakin yana ɗaukar ƙofar gaba da ta baya buɗaɗɗen nau'in kofa.Tabbatar cewa mafi tsayin sassa na leƙen harbin, ciki na ƙofar tare da allon kariya na roba mai jurewa, ƙasa da wurin hulɗar ƙasa kuma yana amfani da roba mai jurewa, don kare ƙofar ba ta karye, kuma yadda ya kamata. hana harbin karfe a wajen bam, tashi daga rauni.

2. Workpiece isar da tsarin

The workpiece isar da tsarin ya hada da dogo da kuma isar trolley.A trolley ba zai iya kawai matsawa a madaidaiciya layi tare da waƙa, amma kuma kawo workpiece a cikin harbi ayukan iska mai ƙarfi dakin a kan karkata frame na trolley don tabbatar da cewa workpiece za a iya yadda ya kamata tsabtace a cikin projectile yankin.

3. Hawaye

Nau'in nau'in guga ne mai lebur mai tuƙi, harsashi yana waldawa, ana amfani da shi don ɗaga cakuda ƙurar pellet ɗin da mai ɗaukar nauyi ya aika zuwa saman injin.Babban motar tuƙi na lif yana ɗaukar babban dabaran bel don ƙara juzu'i, kuma ƙaramin motar yana ɗaukar squirrel keji anti-yashi, anti-slip da anti-deviation.Belin tuƙi yana gudana cikin sauƙi da dogaro, kuma yana ƙara tsawon rayuwar bel ɗin yadda ya kamata.

4. Mai raba

Ayyukan mai raba shi ne don raba pellet ɗin da za a sake yin amfani da su daga cakuda.Sakamakon mai rarrabawa kai tsaye yana rinjayar tasirin tsaftacewa, rayuwar sabis na saka sassa da kuma amfani da pellets.Mai raba kayan aikin yana kunshe da chute, allon ganga mai karkace da kuma dakin rarrabawa.Cakudar pellet da ƙura da injin ɗaga guga ya ɗaga ya shiga cikin ɓangarorin na'urar, wanda aka raba ta cikin allon ganga mai karkace, sannan a aika zuwa hopper bayan rabuwar iska, don tabbatar da aiki na yau da kullun na bindigar fesa.

5, kasa dunƙule conveyor

Ƙarƙashin ɓangaren ɗakin tsaftacewa yana sanye da na'ura mai ɗaukar hoto, wanda zai sauke cakuda ƙurar pellet daga mazurari zuwa kasan lif, kuma ya ɗaga shi zuwa na'ura mai rarraba kayan ta lif.Domin rage zurfin rami, kayan aikin suna ɗaukar na'urori masu ɗaukar hoto guda biyu a tsaye da a kwance don tabbatar da yanayin yanayin harbi na yau da kullun.

6. Bututun isar da wuta

Bututun ciyar da harbi yana da ayyuka biyu, kowane kofa yana ba da kofa don daidaita kwararar bugun harbi don cimma tasirin fashewar harbi, a lokaci guda a ƙarƙashin ƙofar don sarrafa buɗewa da rufewa.Don haka, asarar kayan harbin da ke haifar da leƙen harbin da ba dole ba yana raguwa.

7. Tsarin kawar da kura

Saboda ana yin leƙen harbe-harbe a cikin ɗaki mai rufewa, sabili da haka, yanayin ɗaki na harbi yana da mahimmancin fasaha mai mahimmanci, wanda ke da alaƙa kai tsaye da lafiyar ma'aikaci.Don haka, kayan aikin suna da sanye take da ingantaccen tsarin kawar da ƙura, ta yin amfani da babban daftarin fantsama.Lokacin aiki, lokacin da aka rufe ƙofar ɗakin ɗakin, an haifar da wani mummunan matsa lamba don fitar da iskar gas mai ƙura a cikin ɗakin ɗakin don tacewa.Kayan aikin sun karɓi na yanzu na duniya ci-gaba na bugun jini backblowing tace kura tara, ta yin amfani da sakandare tacewa jiyya, da tsaftataccen kura bayan tace kura fitarwa, ta kura watsi da taro ne kasa da 100 mg/m3, don saduwa da kasa watsi matsayin.

8. Tsarin leƙen asiri:

Domin ya hana korau kwana na workpiece saboda hadaddun surface harbi ayukan iska mai ƙarfi, da kayan aiki sanye take da wani harbi peening tsarin, wanda ake amfani da fesa da korau Angle part don tabbatar da surface jiyya ingancin workpiece.

9. Tsarin haske:

Domin alluran harbi ne da hannu a cikin ɗakin, don haka ɗakin dole ne ya sami ɗan haske.Kayan aiki yana sanye da fitilu 10 a saman ɗakin ɗakin don tabbatar da cewa duk sassan aikin ciki suna da isasshen haske.Matsakaicin haske na cikin gida ya fi 240Lux, akwatin haske an yi shi da gilashi mai tauri don tabbatar da cewa harbin karfe ba zai buge kwan fitila ba, an haɗa firam ɗin akwatin hasken tare da rivets tsakanin jikin ɗakin, da lamba tare da jikin dakin an yi shi da kumfa mai kauri mai kauri na 1.5mm wanda aka lullube shi da sealant, don tabbatar da cewa kura ta cikin gida ba za ta shiga akwatin haske ba kuma ta shafi hasken wuta.

10. Tsarin kula da wutar lantarki

Tsarin kula da wutar lantarki yana ɗaukar kwamiti na al'ada mai sarrafa atomatik, babban matakin sarrafa kansa, ingantaccen aiki, kulawa mai dacewa.

Mai ba da wutar lantarki yana ɗaukar tsarin wayoyi huɗu na matakai uku 380V ± 20V 50HZ

Sashin zagayawa na pellet na tsarin yana ɗaukar kulawar kulle-kulle, kayan aikin za'a iya sarrafa su kawai a jere, manufar sa shine don hana toshewar pellet ɗin da ya haifar da rashin aiki yayin zagawar pellet.A cikin zaɓin abubuwan da aka gyara, duk sun zaɓi samfuran samfuran delixi sanannen gida.

V. Iyakar wadata:

1, dakin taro

2. Saitin yashi 1 na tattara hopper a cikin ƙananan sito:

3, chamber body low sito grid platelebur karfe walda samar, na sama na roba yashi yayyo allon dage farawa daga babba jure lalacewa.

4, kasa a tsaye dunƙule conveyor 4 sets:

5. 1 injin dagawa guga:

6, mai raba yashimai raba gardama) 1

7, tsarin fashewar yashiTankin ajiyar iska 1, bindigogin feshi 2, kayan aikin kariya 2)

8, ƙura mai tarawa: LT-56 bugun jini tace harsashi ƙura tara (shafi bututu, da dai sauransu.)

9, lantarki kula da tsarin: lantarki kula da hukuma, waya, na USB, da dai sauransu

Takardun fasaha da aka kawo tare da kayan aiki: littafin aiki, zane-zane na lantarki, tsarin gabaɗaya da zane-zane na kayan aiki, da zane na asali na kayan aiki.

Vi.Kwanan bayarwa da sharuɗɗan biyan kuɗi

1. Lokacin bayarwa: A cikin kwanaki 60 bayan sanya hannu kan kwangilar tattalin arziki.

2. Sharuɗɗan biyan kuɗi: 30% biya gaba bayan kwangilar ta fara aiki, 60% da 10% biya kafin bayarwa, kuma za a biya lokacin garanti a cikin watanni 3.

Vii.Abubuwan da mai nema zai ɗauka:

1. Mako daya kafin isowar kayan aikin mai kaya, mai bukata sai ya shirya gidauniyar kayan aiki da gina gidaje bisa ga zanen gidauniyar da mai kaya ya tanadar, sannan ya yi shiri kafin shigar da kayan, sannan ya samar da wutar lantarki da iskar gas a wurin.

Abubuwan buƙatun tushen iska: ƙarar ƙura 6.5m3 / min, matsa lamba: 0.5 ~ 0.7mpa

2. Mai nema dole ne ya samar da kayan aikin ɗagawa don tabbatar da amfani da yau da kullun na saukewa da shigarwa akan lokaci.

3. Samar da walda, yankan iskar gas da sauran kayan aikin da mai bayarwa ke buƙata don shigarwa, da kuma samar da masauki ga ma'aikatan shigarwa.

4, anti-skateboard na gefen hanya da babban workpiece harbi peening escalator wanda mai siye zai shirya.

Viii.Alƙawarin mai bayarwa:

1) A cikin kwana ɗaya bayan kwangilar samar da kayayyaki ta fara aiki kuma an karɓi kuɗin gaba, mai siyarwar zai samar da kwafin ginshiƙi na tsarin kayan aiki da kwafi ɗaya na zanen tushe na shigarwa na kayan aiki, kuma ya ba da jagorar fasaha don ginin kafuwar kayan aiki. bisa ga bukatun masu amfani;

(2) Lokacin garanti yana cikin watanni 6 bayan an karɓi kayan aikin kuma an isar da shi zuwa Jam'iyyar A (bangarori masu juriya da lalacewa basa cikin iyakokin garanti).Duk wasu matsalolin masana'antu da ingancin shigarwa a cikin lokacin garanti suna cikin iyakar garantin kyauta na mai kaya (sai dai lalacewa ta wucin gadi).

(3) Lalacewar ɓangarori da sauran hatsarurrukan kayan aiki da ke haifar da rashin yin amfani da Jam'iyyar A da ba ta dace ba za a iya gyara ta mai kaya bayan an tabbatar da bangarorin biyu, kuma Jam'iyyar A za ta biya kuɗin.

(4) Idan akwai babban gazawar kayan aiki, ma'aikatan kula da mai siyarwa zasu isa Party A cikin awanni 24 don magance gazawar tare da Jam'iyyar A.

(5) Mai siyarwar zai ba da horo, laccoci da jagorar wurin ga ma'aikatan kulawa da aiki na jam'iyyar A kyauta.